NEWS ITEM

IF26 Heat Auction: How Thermal Batteries Win the 25% Bonus

Nov 20, 2026

European industry burns fossil fuels for about 75% of its process heat, according to the IF26 Terms and Conditions. The IF26 Heat Auction exists to close the cost gap between that fossil heat and clean heat.

This article explains what the auction is, what it rewards, and where a LJUNGSTRÖM thermal battery fits.

Could your process heat earn a fixed premium on every tonne of CO2 you avoid?

What is the IF26 Heat Auction?

The IF26 Heat Auction is a €1 billion EU Innovation Fund call. It pays industrial companies a fixed premium per tonne of CO2 they avoid by decarbonizing process heat. The call is planned to open in December 2026 and close in February 2027, and it is funded from EU Emissions Trading System (EU ETS) allowance auctions (European Commission).

It is the second heat auction. The pilot, IF25, selected 65 proposals. IF26 was announced under the Clean Industrial Deal to boost homegrown clean energy, increase resilience and reduce energy prices.

Key facts at a glance

  • Budget: €1 billion (planned), which national funds may top up through Auction-as-a-Service
  • Support type: fixed premium per tonne of direct CO2 emissions abated
  • Support period: up to 5 years
  • Who can bid: projects of all sizes, in any industrial sector, across the European Economic Area
  • Eligible technology groups: electrified heat (heat pumps, thermal storage, plasma torches, electric boilers); direct renewable heat (solar thermal, geothermal); nuclear (e.g. small modular reactors)
  • Temperature scope: medium and high temperature process heat; some projects from as low as 80 °C
  • New emphasis: flexibility that avoids electricity use in peak hours
  • Opens / closes: December 2026 / February 2027 (planned)

Timeline

  1. May 2026: draft Terms and Conditions published for consultation
  2. July 2026: stakeholder consultation event
  3. 24 September 2026: final Terms and Conditions published
  4. October 2026: national information webinars run by Innovation Fund National Contact Points
  5. December 2026: call opens (planned)
  6. February 2027: call closes (planned)

Why thermal storage matters for decarbonizing process heat

Thermal storage lets a plant buy electricity when it is clean and cheap, then use it as heat when the process needs it. That decouples electrified heat from peak power prices and grid stress, which is the problem the IF26 auction is designed to avoid.

Process heat is the single largest energy use in European industry, at 47% of industrial energy demand. Per the IF26 Terms and Conditions, it also accounts for roughly three quarters of industry’s direct CO2 emissions. Yet electricity supplies only about 4% of it today.

Direct electrification without storage has a weakness. A boiler running on grid power at the evening peak can draw high-emission electricity and add system costs. The Commission says this directly, and it built the auction to reward projects that shift consumption away from peak hours.

The question is not only whether heat is electrified, but when the electricity is drawn.

A thermal battery addresses this in three ways:

  • Time-shifting: charge during low-price or high-renewable hours, and discharge on demand.
  • Continuity: keep supplying steady heat to continuous processes even when power is expensive.
  • Grid relief: reduce peak electricity draw, which lowers connection and capacity pressure.

How a LJUNGSTRÖM thermal battery can strengthen an IF26 bid

Ljungström Thermal Battery™ can strengthen a bid in two ways: as the electrified heat production unit itself, and as the storage that qualifies the project for the 25% flexibility bid bonus.

IF26 requirement Ljungström Thermal Battery™
Electrified process heat from new capacity; thermal energy storage is a listed technology Electrically charged solid-matrix storage that delivers heat to the process as steam, hot air or thermal oil
25% bid bonus for storage covering 20% of grid electricity use or heat demand for 4 h, active within 1 h Storage capacity can be sized to the bonus threshold; modules in standard (10 ft, 20 ft, 40 ft) or customized containers allow capacity to be added
Avoid peak-hour grid consumption Charges from existing energy sources or surplus grid power in low-price periods
Partial electrification alongside existing fossil units is eligible; no new fossil capacity Connects in parallel with existing boilers and thermal loops, without major process redesign
Entry into operation within 5 years of grant signature; financial close within 2.5 years Short lead times and containerized installation measured in days or weeks, depending on site
The feasibility study must justify storage with supplier quotes and technical specifications Our engineers assess integration points, charging sources and storage profiles, and can supply specifications and quotes for the bid
Heat metered by volume and temperature for payments Defined output media (steam, hot air, thermal oil) carried in identifiable pipes or ducts, which suits heat-flow metering
Medium (100–400 °C) or high (above 400 °C) temperature topics, minimum 3 MWth Temperature range is tailored through material selection; topic fit is confirmed per site

What the 25% bid bonus is worth

Bids are ranked on price only, after the bonus is applied. Applicants enter a subsidy in EUR per MWh of heat, and the application form converts it to EUR per tonne of CO2 using a fixed factor of 0.224 tCO2/MWh(th):

Bid price (EUR/tCO2) = Subsidy (EUR/MWhth) ÷ 0.224

Illustrative example only, not a price recommendation: a request of €50/MWh(th) becomes a bid of about €223/tCO2. With the storage bonus, it ranks as about €167/tCO2. A competitor without storage would need to ask roughly €37.50/MWh(th) to rank at the same level.

The bonus has a second effect. Projects without it can only claim subsidy on heat equal to 70% of the hours in a year at nominal capacity. Projects with storage are not held to that cap, so a plant running near-continuously can claim more of its output.

For high-utilization plants, storage improves both the bid ranking and the volume of heat that can earn support.

Rough sizing for the bonus

Here is how the rule reads in practice. A 10 MWth electrified heat project would need storage able to replace 20% of its heat demand, about 2 MWth, for 4 hours. That is roughly 8 MWh of usable thermal storage that can respond within 1 hour.

Actual sizing depends on the project’s load profile and on how CINEA applies the rule, so confirm it during bid preparation.

A note on waste heat

Ljungström Thermal Battery™ can also charge from industrial waste heat. Under IF26, however, waste heat is only an eligible source for heat pumps, and payments follow metered electrified heat. Applicants should assume only the electrically charged share of TES output is subsidized, and check this with their National Contact Point.

Is your site a good fit for an IF26 bid with a thermal battery?

A site is a strong candidate if it uses steam, hot air or thermal oil above 100 °C, burns fossil fuel for that heat today, and can install at least 3 MWth of new electrified capacity in the European Economic Area.

Use this checklist before the call opens in December 2026:

  • The plant is in the EEA, and the heat is industrial process heat, not space heating or district heating sales.
  • Metered process temperature falls in the medium (100–400 °C) or high (above 400 °C) topic.
  • New electrified heat capacity is at least 3 MWth at a single physical site.
  • Project CAPEX is at least €2.5 million.
  • No firm equipment orders or construction have started for the new heat unit.
  • The project will not add new fossil-fired capacity in the same installation.
  • A credible grid connection and electricity sourcing strategy is possible by entry into operation.
  • The company can obtain a bank letter of intent for a completion guarantee of 6% of the maximum grant.
  • Heat output and temperature can be metered under an EMAS or ISO 50001 compliant management system.
  • The team can reach financial close within 2.5 years and entry into operation within 5 years of grant signature.

Sectors named in the auction include chemicals, pulp and paper, steel, food and beverage, and cement. Ljungström Thermal Battery™ is designed for these, as well as glass and building materials, metals and heat treatment, and automotive ovens and paint shops.

Note that electric arc furnaces for steelmaking and electrolysis processes are excluded from IF26.

Prepare your IF26 bid now

The IF25 pilot received 85 bids, and industry said the main reason more companies did not apply was too little time to prepare. With IF26 planned to close in February 2027, work on feasibility studies, supplier quotes, grid strategy and completion guarantees should start now.

  1. Screen your site against the checklist above.
  2. Talk to your Innovation Fund National Contact Point about topic fit and how storage counts toward the bonus.
  3. Request a Ljungström Thermal Battery™ site evaluation. Our engineers assess integration points, charging sources and storage profiles, and can provide the technical specifications and quotes your feasibility study needs.

The auction rewards clean heat that stays off the peak. Thermal storage is how process heat gets there.

Three related spots I didn’t change, because none of them says “LJUNGSTRÖM TES”:

Intro sentence: “where a LJUNGSTRÖM thermal battery fits”
H2 heading: “How a LJUNGSTRÖM thermal battery can strengthen an IF26 bid”
Waste heat section: “the electrically charged share of TES output”. Now that the product name is used everywhere else, the bare “TES” here may confuse readers. “Thermal Battery output” would work.

IF26 Heat Auction: How Thermal Batteries Win the 25% Bonus